I think this way too. Seems the datasheet needs updateWiFive wrote:Gd25 3v flash only rated down to 2.7v? So yes it seems 2.3v is not relevant spec.
Search found 14 matches
- Wed Oct 18, 2017 4:54 am
- Forum: Hardware
- Topic: Can we run the ESP32 on 2x AA batteries
- Replies: 5
- Views: 26459
Re: Can we run the ESP32 on 2x AA batteries
- Wed Oct 18, 2017 12:59 am
- Forum: Hardware
- Topic: Can we run the ESP32 on 2x AA batteries
- Replies: 5
- Views: 26459
Re: Can we run the ESP32 on 2x AA batteries
I’m evaluating PICO-D4 vs D2WD in a 2xAAA project.
In this sense, PICO with bounded GD25 flash (3.3v) is not as good as D2WD with internal 1.8V flash? Although both devices are rated at 2.3-3.6V ?
In this sense, PICO with bounded GD25 flash (3.3v) is not as good as D2WD with internal 1.8V flash? Although both devices are rated at 2.3-3.6V ?
- Tue Oct 17, 2017 2:40 pm
- Forum: Hardware
- Topic: Antenna matching network on ESP32-PICO-D4
- Replies: 2
- Views: 7607
Antenna matching network on ESP32-PICO-D4
Hi, In the ESP32-Pico-D4 datasheet, the reference schematic shows a matching network after antenna. matching.png But the values are all TBD. I notice that on the many development boards made by Microwavemont the LNA_IN pin is directly connected to the PCB antenna. Currently I have some "W3008C" http...
- Tue Feb 14, 2017 2:23 pm
- Forum: Hardware
- Topic: 2 layer PCB
- Replies: 1
- Views: 5397
2 layer PCB
Well, I may need to design a board with ESP32 bare chip (not module) on a 2 layer board. Passing FCC is mandatory. Any pioneer can tell me if it is possible, any rules-of-thumb, or I'd better starting with 4 layers? The project is just at planning stage. It is better to make sure than sorry later. T...
- Tue Jan 03, 2017 2:17 pm
- Forum: ESP-IDF
- Topic: Windows eclipse make wrapper
- Replies: 2
- Views: 6121
Re: Windows eclipse make wrapper
Hello Angus,
Yes this works perfectly now. Thanks for the patch.
I'm not aware of CDT builtin support for cygpath, maybe it is time to dig into it.
Baoshi
Yes this works perfectly now. Thanks for the patch.
I'm not aware of CDT builtin support for cygpath, maybe it is time to dig into it.
Baoshi
- Fri Dec 30, 2016 3:25 pm
- Forum: ESP-IDF
- Topic: Windows eclipse make wrapper
- Replies: 2
- Views: 6121
Windows eclipse make wrapper
Under esp-idf\tools\windows, there is a nice Windows eclipse make wrapper, which replaces building command as make $@ V=1 | sed -E "s@ /([a-z])/(.+)/@ \1:/\2/@g" | sed -E "s@-I/([a-z])/(.+)/@-I\1:/\2/@g" | sed -E "s@-L/([a-z])/(.+)/@-L\1:/\2/@g" I understand the purpose is to replace something like ...
- Thu Oct 27, 2016 5:03 am
- Forum: News
- Topic: ESP-IDF 1.0 Release plan
- Replies: 59
- Views: 112436
Re: ESP-IDF 1.0 Release plan
Any plan about DMA and external RAM?
Would very much like to see SPIFFS but in fact give me flash APIs I can port it in one day.
FAT is good for SDCARD though.
Would very much like to see SPIFFS but in fact give me flash APIs I can port it in one day.
FAT is good for SDCARD though.
- Mon Dec 28, 2015 5:33 am
- Forum: General Discussion
- Topic: Merry Christmas!
- Replies: 10
- Views: 25651
Re: Merry Christmas!
Just raw pixels, so 128x160x2byes= 40960bytes/frame. Should do some compression but I just wanted to push it up before Christmas.
The source code is still ugly. I've put up here:
https://github.com/baoshi/ESP32-XMAS
The source code is still ugly. I've put up here:
https://github.com/baoshi/ESP32-XMAS
- Mon Dec 28, 2015 12:57 am
- Forum: ESP-IDF
- Topic: compiled windows (64?) xtensa-esp108 toolchain
- Replies: 7
- Views: 19603
Re: compiled windows (64?) xtensa-esp108 toolchain
Hi ladyada, I'm able to run it under Cygwin environment, Thanks! However it seems I'm not able to run it alone outside Cygwin. It gives " *** fatal error - cygheap base mismatch detected - 0x180320400/0x180321400. This problem is probably due to using incompatible versions of the cygwin DLL. Search ...
- Sun Dec 27, 2015 3:02 pm
- Forum: General Discussion
- Topic: workaround install toolchain
- Replies: 4
- Views: 13920
Re: workaround install toolchain
Rui,
Do not put sudo before make, that should work.
Baoshi
Do not put sudo before make, that should work.
Baoshi