ESP32 WROOM 32 Uploading but not working

Prashant
Posts: 7
Joined: Tue Jan 11, 2022 12:56 pm

ESP32 WROOM 32 Uploading but not working

Postby Prashant » Tue Jan 11, 2022 1:09 pm

Hi Team,

I am facing the issue in ESP32 WROOM 32 module like uploading code done but it's not working any GPIOs.

For Example uploading Simple Blink LED its successfully uploaded but LED is not turn on and i am not getting voltage across this.

Kindly give us solution for this.

I am sharing the Schematic please help me out
Attachments
External_Gateway_DSN_1V00_0001 (1).pdf
(5.84 MiB) Downloaded 129 times

ESP_Sprite
Posts: 6359
Joined: Thu Nov 26, 2015 4:08 am

Re: ESP32 WROOM 32 Uploading but not working

Postby ESP_Sprite » Wed Jan 12, 2022 4:00 am

What does your UART output say?

Prashant
Posts: 7
Joined: Tue Jan 11, 2022 12:56 pm

Re: ESP32 WROOM 32 Uploading but not working

Postby Prashant » Wed Jan 12, 2022 4:22 am

Even UART also empty nothing is coming

ESP_Sprite
Posts: 6359
Joined: Thu Nov 26, 2015 4:08 am

Re: ESP32 WROOM 32 Uploading but not working

Postby ESP_Sprite » Wed Jan 12, 2022 11:26 am

What does your UART say when you momentarily short the EN pin to ground?

Prashant
Posts: 7
Joined: Tue Jan 11, 2022 12:56 pm

Re: ESP32 WROOM 32 Uploading but not working

Postby Prashant » Thu Jan 13, 2022 4:40 am

Hi Team,

After Short the EN and Ground pin, I am getting some garbage value. Please refer the attached image.
Attachments
esp32error.PNG
esp32error.PNG (23.42 KiB) Viewed 5293 times

Prashant
Posts: 7
Joined: Tue Jan 11, 2022 12:56 pm

Re: ESP32 WROOM 32 Uploading but not working

Postby Prashant » Thu Jan 13, 2022 6:24 am

Hi Team,

For every time uploading the program need to EN pin Active LOW, Can you please tell me reason why it happed.

Thanks

ESP_Sprite
Posts: 6359
Joined: Thu Nov 26, 2015 4:08 am

Re: ESP32 WROOM 32 Uploading but not working

Postby ESP_Sprite » Thu Jan 13, 2022 9:44 am

Because you don't have an auto-reset circuit. The ESP32 will only go into download mode when you press and hold SW1 and then reset the ESP32.

(As a sidenote: looking at your schematic, C20 is too small. The datasheet advises an 1uF there. In general: we strongly suggest to read and follow the datasheet of your module and also see what the hardware design guidelines document says that applies to your setup.)

Prashant
Posts: 7
Joined: Tue Jan 11, 2022 12:56 pm

Re: ESP32 WROOM 32 Uploading but not working

Postby Prashant » Thu Jan 13, 2022 11:01 am

Hi Team,

Yes sir, we do agree what your said. Even after change the C20 capacitor value 0.1uF to 1uF. Nothing is changed same result we are getting.

Thanks

Prashant
Posts: 7
Joined: Tue Jan 11, 2022 12:56 pm

Re: ESP32 WROOM 32 Uploading but not working

Postby Prashant » Mon Jan 17, 2022 6:20 am

Hi team,

The above schematics work with other circuits can you please explain.

Prashant
Posts: 7
Joined: Tue Jan 11, 2022 12:56 pm

Re: ESP32 WROOM 32 Uploading but not working

Postby Prashant » Thu Jan 20, 2022 7:20 am

Hi Team,

Once done the uploading the code. We made EN pin active low and its working ESP32 module side but Other part like ZigBee is not working what may be the issue. Can you please help me out.

Who is online

Users browsing this forum: No registered users and 34 guests